# New software 3.057 available! - new "fast" rev limiters, launch control, rolling start **URL:** \ **Category:** V3 SOFTWARE\ **Created:** [September 30, 2025, 10:06am UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485 "2025-09-30T10:06:23Z")\ **Posts on this page:** 20\ **Page:** 4
**Author:** ![cmm7v3](https://avatars.discourse-cdn.com/v4/letter/c/73ab20/32.png) [@cmm7v3](https://community.ecumaster.com/u/cmm7v3)\ **Post date:** [October 13, 2025, 12:23pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/61 "2025-10-13T12:23:07Z")
On the log there is an option to log “Idle Air %”, would it be possible to also get “Idle Air % Target”? ---
**Author:** ![Milos](https://avatars.discourse-cdn.com/v4/letter/m/6bbea6/32.png) [@Milos](https://community.ecumaster.com/u/Milos)\ **Post date:** [October 13, 2025, 5:41pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/62 "2025-10-13T17:41:12Z")
Just as an example I founfd some coldstart from last year. It was done on FW\_3.038 in -3°C Battery dropped to 9.7V (never was problem to go lower). As you can see, its clearly visible each turn of engine during cranking on battery voltage the same as on MAP signal. Also labda have no problem to be stable. It was newer the issue during cranking. In PC version also in EDL. ![image](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/3/331e39f92ba1cf25c42594063342efe42915ef24.png) ---
**Author:** ![Jadzwin\_ECUMASTER](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/jadzwin_ecumaster/32/28_2.png) [@Jadzwin\_ECUMASTER](https://community.ecumaster.com/u/Jadzwin_ECUMASTER)\ **Post date:** [October 13, 2025, 5:57pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/63 "2025-10-13T17:57:49Z")
I really cannot reproduce your issue. All is logged, cranking is nothing that can influence the logging (except voltage drop belov 6V) Other option you have the boundled firware with edl logging issue. Then it require pc connection to start edl logging ---
**Author:** ![EsSchiab69](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@EsSchiab69](https://community.ecumaster.com/u/EsSchiab69)\ **Post date:** [October 14, 2025, 6:48pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/64 "2025-10-14T18:48:34Z")
Hi, is there a possibility that we can get user functions that can manipulate whole tables. For example: if the condition in the function is met, multiply the whole airflow ve correction table by 1.1. Or is it already possible and i don’t know how? ---
**Author:** ![michal.kowalski](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/michal.kowalski/32/36_2.png) [@michal.kowalski](https://community.ecumaster.com/u/michal.kowalski)\ **Post date:** [October 15, 2025, 6:48am UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/65 "2025-10-15T06:48:52Z")
It’s already possible. Arithmetic operators can be applied to selected cells by entering a value followed by an operator. For example: • Enter `5+` to add 5 to the selected cells. • Enter `0.5*` to scale down the selected cells by 50%. Available operators: +, −, \*, /, % ---
**Author:** ![EsSchiab69](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@EsSchiab69](https://community.ecumaster.com/u/EsSchiab69)\ **Post date:** [October 15, 2025, 5:13pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/66 "2025-10-15T17:13:20Z")
I think you misunderstood me, so basically what i want to do, is make a user function Fn1, if Fn1 is true make a arithmetic operation e.g. over the whole airflow ve correction table. ![fnctn](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/7/774d7154a06453983adbaab8b5f6edfcafce5d9b.jpeg) ---
**Author:** ![Milos](https://avatars.discourse-cdn.com/v4/letter/m/6bbea6/32.png) [@Milos](https://community.ecumaster.com/u/Milos)\ **Post date:** [October 16, 2025, 7:57am UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/67 "2025-10-16T07:57:08Z")
Dear Jakub, I have to apologize, customer came with the car and I foud **completly loosen battery terminal**. The “issue” is solved. - No PC log issue - No EDL issue - No Lambda issue Sorry to disturbing you from more important work, thank you for hint! ---
**Author:** ![kimbaku](https://avatars.discourse-cdn.com/v4/letter/k/8edcca/32.png) [@kimbaku](https://community.ecumaster.com/u/kimbaku)\ **Post date:** [October 16, 2025, 9:12am UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/68 "2025-10-16T09:12:51Z")
You can activate a custom fuel corection with fn. Then you have a table for ve or lamda target modification ---
**Author:** ![T1BRAY](https://avatars.discourse-cdn.com/v4/letter/t/b2d939/32.png) [@T1BRAY](https://community.ecumaster.com/u/T1BRAY)\ **Post date:** [October 16, 2025, 2:08pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/69 "2025-10-16T14:08:26Z")
Under outputs on 57 when using the quick tabs at the top . I can choose fuel pump parameters and when I return or restart it always says (electric Water pump ) parameters.. may be a bug . ---
**Author:** ![Turbofreak](https://avatars.discourse-cdn.com/v4/letter/t/87869e/32.png) [@Turbofreak](https://community.ecumaster.com/u/Turbofreak)\ **Post date:** [October 17, 2025, 10:47pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/70 "2025-10-17T22:47:53Z")
Imperial/Metric conversion issue discovered in Graph log Sensor Setup / Custom Temp channels. Imperial-Pre-IC custom channel temp 28F (-2C) ![](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/d/d9ecb386580d089b1175e51302ffd86317355e9c.png) When switched to Metric-Pre IC Custom temp 1 channel shows -6C (21F) vs -2C ![](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/6/619d15c3dbb4ae01c1b0dedef8983b1a3ddcfa11.png) ---
**Author:** ![baxtercrafter](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/baxtercrafter/32/2130_2.png) [@baxtercrafter](https://community.ecumaster.com/u/baxtercrafter)\ **Post date:** [October 18, 2025, 6:41pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/71 "2025-10-18T18:41:13Z")
Why is there always a map error in the logbook for no reason? ---
**Author:** ![gtengines](https://avatars.discourse-cdn.com/v4/letter/g/8dc957/32.png) [@gtengines](https://community.ecumaster.com/u/gtengines)\ **Post date:** [October 20, 2025, 3:15pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/72 "2025-10-20T15:15:54Z")
![image](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/4/4c39dd93bb089e60558d6c4eab9a889bbefad936.png) Hello Jakub. Why thoose limitations allways? 😃 Why cant set max assync enrich. rpm lower than 2000? also check the log…tps rate max 220..async enrich table -100 and enrychment still happend ---
**Author:** ![gnutz2](https://avatars.discourse-cdn.com/v4/letter/g/73ab20/32.png) [@gnutz2](https://community.ecumaster.com/u/gnutz2)\ **Post date:** [October 23, 2025, 8:59pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/73 "2025-10-23T20:59:39Z")
Feedback on the PMU analogs. Working fine receiving ana1-8 from PMU but now I’m unable to receive a message on the remaining CAN ana inputs. When ana 1 from ADU is sent on 0X510 the message shows in light client fine but Black wont receive, constantly showing 5v when actual is 2.35v. ![Screenshot 2025-10-23 195329](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/9/94cc05e300b98fc5633703e81d24a95b6137da22.png) ![Screenshot 2025-10-23 195158](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/3/36bef6993760b053a6bbb7c71c5d67546b1056f1.png) ---
**Author:** ![Hussain\_bo\_Hamad](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/hussain_bo_hamad/32/839_2.png) [@Hussain\_bo\_Hamad](https://community.ecumaster.com/u/Hussain_bo_Hamad)\ **Post date:** [October 24, 2025, 1:41am UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/74 "2025-10-24T01:41:59Z")
These corrections tablets are missing, you cant even choose ignition in custom corrections. ![IMG_20251024_043857](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/0/0539238ba85b59c1b16ff3181e66f509902ca410.jpeg) ---
**Author:** ![Jadzwin\_ECUMASTER](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/jadzwin_ecumaster/32/28_2.png) [@Jadzwin\_ECUMASTER](https://community.ecumaster.com/u/Jadzwin_ECUMASTER)\ **Post date:** [October 25, 2025, 10:07pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/75 "2025-10-25T22:07:05Z")
> [@T1BRAY](#): > > Under outputs on 57 when using the quick tabs at the top . I can choose fuel pump parameters and when I return or restart it always says (electric Water pump ) parameters.. may be a bug . It is not possible due to the system architecture. ---
**Author:** ![Jadzwin\_ECUMASTER](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/jadzwin_ecumaster/32/28_2.png) [@Jadzwin\_ECUMASTER](https://community.ecumaster.com/u/Jadzwin_ECUMASTER)\ **Post date:** [October 25, 2025, 10:07pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/76 "2025-10-25T22:07:37Z")
> [@T1BRAY](#): > > says Already fixed for version 3.058 ---
**Author:** ![Jadzwin\_ECUMASTER](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/jadzwin_ecumaster/32/28_2.png) [@Jadzwin\_ECUMASTER](https://community.ecumaster.com/u/Jadzwin_ECUMASTER)\ **Post date:** [October 25, 2025, 10:08pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/77 "2025-10-25T22:08:14Z")
Already fixed for 3.058 ---
**Author:** ![Jadzwin\_ECUMASTER](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/jadzwin_ecumaster/32/28_2.png) [@Jadzwin\_ECUMASTER](https://community.ecumaster.com/u/Jadzwin_ECUMASTER)\ **Post date:** [October 25, 2025, 10:10pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/78 "2025-10-25T22:10:43Z")
Already changed to 500 in 3.058 ---
**Author:** ![Jadzwin\_ECUMASTER](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/jadzwin_ecumaster/32/28_2.png) [@Jadzwin\_ECUMASTER](https://community.ecumaster.com/u/Jadzwin_ECUMASTER)\ **Post date:** [October 25, 2025, 10:14pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/79 "2025-10-25T22:14:20Z")
Now there are 3 3D custom tables for ingition corrections. It gives you much more freedom. ---
**Author:** ![Jadzwin\_ECUMASTER](https://dub1.discourse-cdn.com/flex013/user_avatar/community.ecumaster.com/jadzwin_ecumaster/32/28_2.png) [@Jadzwin\_ECUMASTER](https://community.ecumaster.com/u/Jadzwin_ECUMASTER)\ **Post date:** [October 25, 2025, 10:26pm UTC](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485/80 "2025-10-25T22:26:34Z")
You need to set different multiplier and divider. ![image](https://europe1.discourse-cdn.com/flex013/uploads/ecumaster/original/2X/1/1483171107b80fa0aadd66203aa87b725f6e1eaf.png) [Previous page](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485.md?page=3) [Next page](https://community.ecumaster.com/t/new-software-3-057-available-new-fast-rev-limiters-launch-control-rolling-start/4485.md?page=5)