Hey Guys, Can Someone explain What is meant in Emu Software With vag torque ? For What is This value and What is the effect by changing it from 400 to 600Nm. I hope someone can help, have a good one:) I got only 13bar clutch pressure and in vcds the torque doesnt Show More than 410Nm doesnt matte…

Yes, it’s the same situation. The light on the instrument bothers me a lot. It doesn’t seem to appear with any regularity.

Is your problem solved? It seems that he has the same problem. [image] EMU Black - ABS Coding in CAN setup EMU BLACK / CLASSIC Howdy ECU Master peeps. I have a 2010 2.0TSI 4motion Tiguan with a VW Passat BWS R36 turbo’d engine swap running a EMU Black ECU. I am trying t…

Hi, Problem is not solved…Still have the 2 lights on the dash boards. I am sure its to do with the EMU Black Vehicle can not set correctly. Also not sure if it matters but my car has a manual transmit and its always been a manual.

EMU Black - ABS Coding in CAN setup The codes in VCDS are, ABS Module Hardware :- 5N0 614 109 M 01314 - Engine Control Module 000 - - 01044 - Control Module Incorrectly Coded 000 The errors i have in VCDS are, ABS Module Hardware :- 5N0 614 109 M 01314 - Engine Control Module 000 - - 01044…

Hi Apow, i cant figure out what the problem is. In manual i didnt had problems. I am thinking about to switch to Maxxecu. The only problem in manual state was that the haldex had sometime a fault. I dont know the Code anymore but it says no communication to ECU and the traction control light com…

Hi AlexJo174, My problem is that the my car was originally a Manual car i swapped the engine out to. The only components that have been changed on the vehicle are the engine (For a VW R36), gearbox from a Diesel Tiguan and the ECU which is a EMU Black. Everything works fine apart from the ABS, Au…

Have you guys done the basic troubleshooting on the CAN bus wiring? Have you tested what ohms you are getting from can-h to can-l to eliminate any network config issues? Blaming the ECU at this point is just going to end up costing you more in the long run as you are expecting the ECU to know wh…

Hi @MickyMcFinnigan , This is really informative and I will look in to making sure the CAN connections are as you mentioned. Thx. Just to confirm my Tiguan was a 2.0TSI 4motion manual, which has been swapped with a VW Passat R36 which has been turbocharged with a modified Tiguan manual gearbox. Not…

Hi @MickyMcFinnigan , in my case, my Audi A3 is from 2004 original with manual gearbox. I only changed the gearbox to a HXX from passat R36 and added a CanChecked MFD15 Can Gauge, that worked very well with the manuel gearboxe state. I took the coding from my friends A3 ( original DSG car ) so the …

[image] Second can-bus in/outputs on 1.8t BAM plug&play emu black? EMU BLACK / CLASSIC If you add termination resistor then yes. maybe was the end resistor youre problem by taking the canbus from the extra extra pnp connector??

Dq250 dsg cxx vr6turbo

EMU BLACK / CLASSIC

caddymaxi500 May 25, 2024, 5:36pm 19

maybe was the end resistor youre problem by taking the canbus from the extra extra pnp connector??

Topic		Replies	Views
VAG MDI torque on DSG DQ250 EMU BLACK / CLASSIC	1	396	November 10, 2024
Version 3.063 BETA V3 SOFTWARE	74	3851	April 18, 2026
New software 3.043 available! V3 SOFTWARE	79	4686	June 13, 2025
EMU Black - ABS Coding in CAN setup EMU BLACK / CLASSIC	8	1476	July 17, 2024
Emu black dsg problem EMU BLACK / CLASSIC	11	1288	September 5, 2024

Dq250 dsg cxx vr6turbo

Related topics